Wednesday, August 13, 2014
Mains Remote Alert
Transmitter parts:
R1____________220K 1/4W Resistor
R2____________470R 1/2W Resistor
R3____________100K 1/4W Resistor
R4______________1K 1/4W Resistor
C1_____________10nF 400V Ceramic or Polyester Capacitor
C2____________330nF 400V Polyester Capacitor
C3______________1n5 63V Ceramic Capacitor (See Notes)
C4_____________10nF 63V Ceramic or Polyester Capacitor
C5____________100µF 25V Electrolytic Capacitor
D1,D2________1N4007 1000V 1A Diodes
D3_________BZX79C30 30V 500mW Zener Diode
Q1,Q2_________BC546 65V 100mA NPN Transistors
L1_______________IF Transformer for AM receivers, 445-470KHz
P1_____________SPST Mains suited Pushbutton
PL1____________Male Mains plug & cable
Receiver schema diagram:
Receiver parts:
R1____________220K 1/4W Resistor
R2____________470R 1/2W Resistor
R3____________150K 1/4W Resistor
R4______________2K2 1/4W Resistor
R5____________100K 1/4W Resistor
R6_____________47K 1/4W Resistor
R7______________2K2 1/4W Resistor (Optional)
C1____________100nF 400V Polyester Capacitor
C2____________330nF 400V Polyester Capacitor
C3______________1n5 63V Ceramic Capacitor (See Notes)
C4,C6_________330pF 63V Ceramic Capacitors
C5,C7_________100µF 25V Electrolytic Capacitors
D1,D2________1N4007 1000V 1A Diodes
D3_________BZX79C12 12V 500mW Zener Diode
D4,D5,D6_____1N4148 75V 150mA Diodes
D7_____________5mm. Red LED (Optional)
Q1,Q2_________BC547 45V 100mA NPN Transistors
L1_______________IF Transformer for AM receivers, 445-470KHz
BZ1___________Piezo sounder (incorporating 3KHz oscillator)
PL1____________Male Mains plug & cable
Transmitter schema operation:
Q1 and Q2 are wired as a Darlington pair to obtain the highest possible output from a Hartley type oscillator running at about 135KHz frequency. The 230Vac mains is reduced to 30Vdc without the use of a transformer by means of C2 reactance, a two diode rectifier cell D1 & D2 and Zener diode D3.
The oscillator output is taken from L1 secondary winding and injected into the mains wiring by means of C1.
Receiver schema operation:
The 135KHz sinewave generated by the transmitter is picked-up from mains wiring by C1 and selected by the tuned schema L1-C3. Q1 greatly amplifies the incoming sinewave and converts it in a 12V-peak squarewave. D4 & D5 limit the input voltage at Q1 base to less than 1V-peak to avoid damaging of the transistor due to the high voltage transients frequently occurring on the mains line. D6 eliminates any negative component of the signal and Q2 drives the load. C7 is necessary to smooth the signal residues appearing across the load.
The 12Vdc supply for this unit is obtained as described above for the transmitter schema.
Notes:
* Transmitter and receiver coils L1s must be tuned regulating their ferrite cores to obtain maximum output at C3 leads, either in transmitter and receiver.
* This setup is better done using an oscilloscope and placing the two units as far as possible to each other.
* The tuning of the coils at 135KHz frequency should be obtained with the ferrite core almost totally inserted in its slot, if 455KHz IF transformers are used for both L1s.
* Using IF transformers different from those specified, a change in both C3s value could be needed. The value of these capacitors may vary from 1 to 3.3nF but must be the same in transmitter and receiver.
* The load can be a beeper, a LED or both. Omitting the beeper and choosing the LED as the only load, its limiting resistor R7 should be reduced in value to about 1K, to increase device brightness. In this case, a 10mm. diameter LED type or greater, can also be useful .
* Warning! These units are connected to 230Vac mains, then some parts in the schema boards are subjected to lethal potential! Avoid touching the diagram when plugged and enclose them in plastic boxes.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment